https://drive.google.com/folderview?id=0Bxdf_3fzbUgSNnI5eGJsMjBtRzg&usp=sharing
커널 확인사항
CONFIG_VIDEO_TV20=y
CONFIG_HDMI_CEC=y
CONFIG_HDMI_HPD=y
|
안드로이드 확인 사항
"device/crazyboys/mango210/BoardConfig.mk" 파일에 아래 내용이 있어야 합니다.
S5P_BOARD_USES_HDMI := true
ifeq ($(S5P_BOARD_USES_HDMI),true)
BOARD_HDMI_STD := STD_1080P
S5P_BOARD_USES_HDMI_SUBTITLES := true
Endif
|
소스 이미지를 받습니다.
http://crztech.iptime.org:8080/Release/mango210/android/ics/2014_0325/m210_ics404_nand_boot_image.tgz
소프트 사양
OS : Android Ice Cream Sandwitch 4.0.4
Board : mango210, CM-V210+ CX-V210
LCD : 7" LCD (with press touch)
- How to
$ tar xf m210_ics404_nand_boot_image.tgz
$ cd image
Micro SD card PC에 삽입
[icanjji@icanjji-pc image]$ df
Filesystem 1K-blocks Used Available Use% Mounted on
/dev/sda2 1947374844 1571937152 277975584 85% /
udev 2006136 4 2006132 1% /dev
tmpfs 402988 2132 400856 1% /run
none 5120 0 5120 0% /run/lock
none 2014924 76 2014848 1% /run/shm
/dev/sda1 96880 124 96756 1% /boot/efi
/dev/sdg4 103736 4152 94232 5% /media/6627d2f3-3ec0-70ce-dc9a-4967b533e741
/dev/sdg2 231976 158576 73400 69% /media/57f8f4bc-abf4-655f-bf67-946fc0f9f25b
/dev/sdg3 348264 57828 272460 18% /media/d0eb02fa-3408-a1d4-0da1-796dab7b1748
/dev/sdg1 7070048 48 7070000 1% /media/0000-3333
$ sudo ./sdwriter <device node> 210 bin
ex)$ sudo ./sdwriter sdg 210 bin
Micro SD Card를 Board에 삽입 (SD slot 2)
Boot Switch 변경
Mango210 : 1, 3, 4 ON
CM-V210+ CX-V210 : 2, 3, 6 ON
전원, usb otg cable, 3pin Serial 케이블 연결 후 , 부팅을 합니다.
부팅 후 터미널 프로그램에서
u-boot 실행 되자 마자 아무키나 눌러서 , u-boot 명령창으로 들어갑니다.
소스 이미지를 받습니다.
http://crztech.iptime.org:8080/Release/mango210/android/ics/2014_0325/m210_ics404_nand_boot_image.tgz
소프트 사양
OS : Android Ice Cream Sandwitch 4.0.4
Board : mango210, CM-V210+ CX-V210
LCD : 7" LCD (with press touch)
- How to
$ tar xf m210_ics404_nand_boot_image.tgz
$ cd image
Micro SD card PC에 삽입
[icanjji@icanjji-pc image]$ df
Filesystem 1K-blocks Used Available Use% Mounted on
/dev/sda2 1947374844 1571937152 277975584 85% /
udev 2006136 4 2006132 1% /dev
tmpfs 402988 2132 400856 1% /run
none 5120 0 5120 0% /run/lock
none 2014924 76 2014848 1% /run/shm
/dev/sda1 96880 124 96756 1% /boot/efi
/dev/sdg4 103736 4152 94232 5% /media/6627d2f3-3ec0-70ce-dc9a-4967b533e741
/dev/sdg2 231976 158576 73400 69% /media/57f8f4bc-abf4-655f-bf67-946fc0f9f25b
/dev/sdg3 348264 57828 272460 18% /media/d0eb02fa-3408-a1d4-0da1-796dab7b1748
/dev/sdg1 7070048 48 7070000 1% /media/0000-3333
$ sudo ./sdwriter <device node> 210 bin
ex)$ sudo ./sdwriter sdg 210 bin
Micro SD Card를 Board에 삽입 (SD slot 2)
Boot Switch 변경
Mango210 : 1, 3, 4 ON
CM-V210+ CX-V210 : 2, 3, 6 ON
전원, usb otg cable, 3pin Serial 케이블 연결 후 , 부팅을 합니다.
부팅 후 터미널 프로그램에서
Nand 데이터를 지웁니다.
|
MANGO210 # nand scrub
NAND scrub: device 0 whole chip
Warning: scrub option will erase all factory set bad blocks!
There is no reliable way to recover them.
Use this command only for testing purposes if you
are sure of what you are doing!
Really scrub this NAND flash? <y/N>
Erasing at 0x0 -- 0% complete.
nand0: MTD Erase failure: -5
Erasing at 0x35c0000 -- 21% complete.
nand0: MTD Erase failure: -5
Erasing at 0xa8e0000 -- 66% complete.
nand0: MTD Erase failure: -5
Erasing at 0xffe0000 -- 100% complete.
Scanning device for bad blocks
OK
“fastboot” 명령 입력
|
MANGO210 # fastboot
Fastboot: employ default partition information
[Partition table on NAND]
ptn 0 name='bootloader' start=0x0 len=0x100000(~1024KB)
ptn 1 name='kernel' start=0x100000 len=0x500000(~5120KB)
ptn 2 name='ramdisk' start=0x600000 len=0x300000(~3072KB)
ptn 3 name='system' start=0x900000 len=0xA000000(~163840KB) (Yaffs)
ptn 4 name='cache' start=0xA900000 len=0xA00000(~10240KB) (Yaffs)
ptn 5 name='userdata' start=0xB300000 len=N/A (Yaffs)
Linux pc에서 Write 하기
< board <-> mini usb calbe <-> linux pc >
|
# sudo ./fastboot-linux.sh
Write 이미지 완료 후
보드에서
Boot switch 변경
Mango210 : 1, 2 ON
CM-V210 + CX-V210 : 1, 6 ON
# sudo ./fastboot reboot
또는
리셋 합니다.
# logcat &
D/SecTVOutService( 2158): SecTVOutService instantiate
D/libfimc ( 2158): SecFimc::SecFimc()
D/SecTVOutService( 2158): virtual void android::SecTVOutService::setHdmiStatus(uint32_t) HDMI cable status = 1
D/libfimc ( 2158): SecFimc::create(fimc_dev: 1, fimc_mode: 3, buf_num: 1)
D/libfimc ( 2158): bool SecFimc::create(int, int, unsigned int):: /dev/video1
D/libfimc ( 2158): fimc1 fd = 23
|
댓글 없음:
댓글 쓰기